Hotline
Application / News

Share: 4 special plating methods in circuit board plating

Four special plating methods in circuit board plating. This article mainly introduces 4 special plating methods in circuit board welding.

1 Finger row electroplating

It is often necessary to plate rare metals on board edge connectors, board edge protruding contacts or gold fingers to provide lower contact resistance and higher wear resistance. This technology is called finger row plating or protrusion plating . Gold is often plated on the protruding contacts of the board edge connector with the inner plating layer of nickel. The gold fingers or the protruding parts of the board edge are manually or automatically plated. At present, the gold plating on the contact plug or gold finger has been plated or leaded. , Instead of plated buttons.

The process is as follows:  1) Strip the coating to remove the tin or tin-lead coating on the protruding contacts     2)   Rinse with washing water     3)   Scrub with abrasive scrubbing     4)   activation in 10%   sulfuric acid 5) Plating on the protruding contacts The thickness of nickel is 4 -5μm  6) cleaning and demineralizing water  7) gold penetration solution treatment  8) gold plating 9) cleaning  10) drying   

2 Through hole plating 

There are many ways to build a satisfactory plating layer on the hole wall of the substrate drilled hole. This is called hole wall activation in industrial applications. The commercial production process of printed circuits requires multiple intermediate storage tanks. Each storage tank has its own control and maintenance requirements. Through-hole plating is a necessary follow-up process of the drilling process. When the drill bit drills through the copper foil and the substrate underneath, the heat generated melts the insulating synthetic resin that constitutes most of the substrate matrix, the molten resin and other drilling debris It is piled up around the hole and coated on the newly exposed hole wall in the copper foil. In fact, this is harmful to the subsequent electroplating surface. The molten resin will also leave a layer of hot shaft on the hole wall of the substrate, which exhibits poor adhesion to most activators, which requires the development of a class of similar stain removal and etch-back chemical technologies.    A method that is more suitable for printed circuit board prototyping is to use a specially designed low-viscosity ink to form a high-adhesion, high-conductivity film on the inner wall of each through hole. In this way, there is no need to use multiple chemical treatment processes, only one application step, followed by thermal curing, can form a continuous film on the inner side of all the hole walls, which can be directly electroplated without further treatment. This ink is a resin-based substance that has strong adhesion and can be easily adhered to the walls of most thermally polished holes, thus eliminating the step of etchback.    

3 scroll wheel linkage type selective plating

The pins and pins of electronic components, such as connectors, integrated circuits, transistors, and flexible printed circuits, all use selective plating to obtain good contact resistance and corrosion resistance. This electroplating method can be manual or automatic. It is very expensive to individually select and plate each pin, so batch welding must be used. Usually, the two ends of the metal foil that is rolled to the required thickness are punched, cleaned by chemical or mechanical methods, and then selectively used such as nickel, gold, silver, rhodium, button or tin-nickel alloy, copper-nickel alloy , Nickel-lead alloy, etc. for continuous electroplating. In the electroplating method of selective plating, first coat a layer of resist film on the part of the metal copper foil board that does not need to be electroplated, and electroplating only on the selected part of the copper foil.    

4 Brush plating  

Another method of selective plating is called “brush plating” . It is an electrodeposition technique, and not all parts are immersed in the electrolyte during the electroplating process. In this kind of electroplating technology, only a limited area is electroplated, and there is no effect on the rest. Usually, rare metals are plated on selected parts of the printed circuit board, such as areas such as board edge connectors. Brush plating is used more when repairing discarded circuit boards in electronic assembly workshops. Wrap a special anode (a chemically inactive anode, such as graphite) in an absorbent material (cotton swab) , and use it to bring the electroplating solution to the place where it needs to be electroplated.

Prev:
Next: